Prefabricated homes EPS concrete cement sandwich partition wall
panels
Our company:
Hubei Boyuejia Industrial Co., Ltd is a high-tech enterprise integrating the R&D,
production,sale and installation of new energy-saving lightweight wall materials
such as eps sandwich panel,wall panel, wall tiles and the manufacture of relevant
machinery product line . In an active responseto the national policy about wall
material reforming, our company has fully absorbed the advanced
technologies
from home and abroad.
Composite:
Calcium silicate board(face panel) + Cement and EPS(core) + Calcium
silicate board(face panel)
Specification:
| Length (mm) | Width (mm) | Thickness (mm) | Density (kg/m2) | Application | Appearance |
2270
2440
2700
3000 | 610 | 50 | 38±5 | Non-load bearing wall of houses and buildings | With reinforced calcium silicate board as face board, solid |
| 60 | 42±5 |
| 75 | 45±5 |
| 90 | 52±5 |
| 100 | 56±5 |
| 120 | 62±5 |
| 150 | 72±5 |
| 180 | 85±5 |
| 200 | 95±5 |
Index:
| NO. | Item | National Standards | Testing Results |
| 60mm | 90mm | 120mm | 60mm | 90mm | 120mm |
| 1 | Anti-impact performance/times | ≥5 | ≥5 | ≥5 | ≥6 | ≥6 | ≥10 |
| 2 | Anti-bending damage load/times over deadweight | ≥1.5 | ≥1.5 | ≥1.5 | ≥3 | ≥3 | ≥3 |
| 3 | Anti-pressure strength /Mpa
| ≥3.5 | ≥3.5 | ≥3.5 | ≥6 | ≥6 | ≥6 |
| 4 | Surface density kg/m2 | ≤70 | ≤90 | ≤110 | ≤45 | ≤54 | ≤66 |
| 5 | Single point hanging Strength /N | ≥1000 | ≥1000 | ≥1000 | ≥1000 | ≥1200 | ≥1300 |
| 6 | Fire proof limit /h | ≥1 | ≥1 | ≥1 | ≥3 | ≥3 | ≥4 |
| 7 | Sound insulation capacity in the air /Db | ≥30 | ≥35 | ≥40 | ≥35 | ≥40 | ≥45 |
| 8 | Soften coefficient | ≥0.80 | ≥0.80 | ≥0.80 | ≥1 | ≥1 | ≥1 |
| 9 | Moisture rate a/% | ≤12 | ≤10 | ≤10 | ≤10 | ≤9 | ≤7 |
| 10 | Heat transfer coefficient w/m2.k | ≤2.0 | ≤2.0 | ≤2.0 | ≤1.0 | ≤0.6 | ≤0.5 |
| 11 | Drying shrinkage /mm/m | ≤0.6 | ≤0.6 | ≤0.6 | ≤0.45 | ≤.0.5 | ≤0.5 |
| 12 | Inner radiation index
| ≤1 | ≤1 | ≤1 | ≤1 | ≤1 | ≤1 |
| 13 | Outer radiation index
| ≤1 | ≤1 | ≤1 | ≤1 | ≤1 | ≤1 |
| 14 | Radioactivity Limit | ≤1 | ≤1 | ≤1 | ≤1 | ≤1 | ≤1 |
Installation Steps:
1. Setting the line and carrying the board into position
2. Using hand-hold electric saw freely according to the
specification of wall,
3. Sizing the bump slot and then spread the baseline and the bump
slots with the Boyuejia
special adhesives
4. Carrying the board prepared to be installed to the installation
place, correcting the wall board
by Special tools, and making it close tightly, and let the polymer
mortar squeeze out into full and
then fixing it with a wedge temporarily
5. Correcting, fixing
Using a guiding rule of two meters to check the vertical and
leveling correction. Then using 6mm
or 8mm reinforcing steel bar and ribs adding with construction
sealant to fix.
6. Grooving and piping
Cutting a groove by a hand-hold electric saw for burying the
concealed wire and switch box.
Then filling with polymer mortar after installation.
7. Sticking anti-cracking tape
8. Installing doorcase
9. Facing ceramic tile, decorative sheet, coating and wall paper
sticking ceramic tiles,
or wood facing panels and coating directly on the installed wall
without plastering.
Certification:
